VitroINK® 3D – Bioink Starter Kit
VitroINK® 3D Bioink Starter Kit contains both bioink and the complete mixing kit to prepare the cell/bioink mixture for 3D bioprinting. The kit includes a 3 mL or 10 mL VitroINK 3D and a complete mixing kit that includes a dispenser, 1 mL syringe, 3 mL syringe, connectors and mixing head to get you started.
VitroINK 3D is a ready-to-use tunable bioink for 3D bioprinting. The pure hydrogel matrix structure is good for cell spheroid formation and supporting the growth of cells requiring low cell-matrix interactions.
VitroINK Mixing Kit was designed to provide a robust mixing of bioink and cells. Cells can be prepared with VitroINK for a 3:1 mixing ratio using the 3 mL syringe or a 10:1 mixing ratio using the 1 mL syringe. Put the VitroINK and cell suspension in the mixer and gently press the mixture through the connector and mixing head to your bioprinter cartridge. Wait 10-20 minutes for the mixture to stabilize before printing. There is no UV, no temperature/pH curing, or chemical cross-linking for the VitroINK system. Simply adding cell culture medium to cover the printed structure can further stabilize and support cell growth. The bioprinted cells are ready for incubation.
- Need a customized bioink? Contact us for a quote.
- Need rheology data of VitroINK with your medium and mixture for publication? Check our data support service.
Kit Contents & Specifications
- Xeno-free tunable bioink for 3D bioprinting.
- Ready-to-use at room temperature
- No UV, temperature/pH curing or chemical cross-linking required
- Neutral pH
- Transparent. Excellent visibility after printing and cell culture
- Pre-mix with cells using the VitroINK Mixing Kit
- Ships room temperature. Store at 2-8°C
- Size: 3 mL and 10 mL
VitroINK Mixing Kit
- Complete mixing kit. Includes:
(1) 1 mL syringe
(1) 3 mL syringe
(1) connector and tubing
- (1) mixing head
- Use for 3:1 or 10:1 mixing ratio
- Size: 3 mL and 10 mL
Handbooks and Resources
Data and References
Figure 1. Rheological properties of VitroINK 3D under the time sweep and temperature sweep tests.A) The time sweep test of VitroINK 3D without or with 3:1 and 10:1 (v/v) mixing with DMEM medium. The elastic modulus was tested at room temperature and showed a feasible range for extrusion printing before incubation with cell culture medium. B) the elastic modulus and viscosity properties of VitroINK 3D under the temperature sweep testing (20 to 40°C). The elastic modulus and viscosity are relatively stable at 20 to 36°C. When temperatures higher than 36, the elastic modulus and viscosity decrease. The data indicate the VitroINK has a wide range of working temperatures and can be easily used at room temperature or physiological temperature.
Figure 2. Shear-thinning and rapid recovery property of VitroINK 3D. A) The shear-thinning property of VitroINK under the shear rate from 0.1 to 100 HZ. B) the amplitude sweep test shows the shear thinning and rapid recovery property of VitroINK under the shear strain change from 0.1 to 500% in two circles. With this unique shear-thinning and rapid recovery mechanical property, VitroINK can well maintain the printed structure after extrusion.
g>Figure 4. The printed line width of VitroINK 3D with 22G, 25G, 27G nozzle at different pressures and print speeds. The line width decreases as the print speed increases. At lower printing pressures, lines can only be printed continuously under low print speed. (VitroINK was printed by using Cellink INKCREDIBLE+ 3D bioprinter)
Figure 5. POI value of VitroINK 3D with 22G, 25G, 27G nozzle at different pressures and print speeds. For all three nozzle sides, the print speed at 3 mm/s gives the highest POI value at low pressure. Under a fixed pressure, the faster print speed gives a higher POI value.
Figure 6. Adjusted printing conditions after mixing VitroINK with Cell culture medium. Mixing at 3:1 (A) or 10:1 (B) ratios by using VitroINK mixing kit. The line width increase after mixing. Adjust the printing speed from 3 to 7 or 5 mm/s can bring the line width down.
Figure 7. Glioblastoma cell line (SNB 75) cultured in VitroINK 3D (3:1 bioink: cells mixing) at day 4.